Search Results
Radiall ODC Series Outdoor Fibre Optic Connectors & Assemblies
The ODC® connector was designed for FTTA (Fibre-To-The-Antenna) outdoor links in Telecom wireless applications.
N type connectors size, screw coupling, robust waterproof connector to withstand harsh environmental conditions and weather.
Designed for UMTS networks, 3rd generation or higher.
These fibre optic transmission lines allow data to travel at the speed of light with practically no loss.
Cable assemblies available in 2 or 4 channels, multimode and singlemode.
GPS Active 2 Way Power Divider for L1/L2 & GLONASS with DC Injector
This device is an active 2 way divider designed for vehicle application allowing the signal from a single GPS antenna to be shared between two receivers. The unit is configured to insert 5 Volts DC to the antenna via the three pin power connector, while the output ports are DC loaded to Simulate current draw draw. DC is blocked to the 2 output ports, supplied to the input port.
GPS 2 & 4 Way Splitter / Dividers
Medium Power, L Band 1200-1650 MHz, Port 2 DC Blocked
Rojone’s AMA-2300-XN Series of power dividers are specifically designed for GPS applications.
Output 1 is AC coupled to the input while Output 2 is DC coupled to allow for two receivers to a single active antenna. The receiver connection to the power divider’s DC path will be able to pass DC to the antenna. The DC current capability is > 500mA.
L1/L2 Splitters are also available; please contact Rojone Pty Ltd.
Miniature GPS 2 & 4 Way Splitter / Dividers
Rojone’s AMA-2251-1400 Series of miniature dividers are specifically designed for space critical GPS applications. One output is AC coupled to the input while the other is DC coupled to allow for two receivers to a single active antenna. The receiver connection to the power divider’s DC path will be able to pass DC to the antenna. The DC current capability is > 500mA.
GPS 6 Way Splitter / Dividers
AMA-2301-6N is specifically designed for L1, L2 and GLONSS receivers. This divider incorporates 6 diodes to provide DC through from each output to the antenna with 20dB Isolation; this allows any one port to supply DC while the diodes block the other ports. Six resistors apply a DC load to allow the GPS receivers to operate.
Miniature GPS 8 Way GPS Splitter / Dividers
Rojone’s AMA-2251-8MS is a miniature 8 way dividers are specifically designed for space critical GPS applications. One output is AC coupled to the input while the other is DC coupled to allow for two receivers to a single active antenna. The receiver connection to the power divider’s DC path will be able to pass DC to the antenna. The DC current capability is > 500mA
Rojone – GPS Product Guide
Rojone has a full range of GPS products, to download a copy of our GPS catalogue click on the link below.
Rojone makes available two GPS amplifiers in our AMA-061 Series.
AMA-061B is our broadband GPS Amplifier and our AMA-061F is a high rejection GPS filtered. Both these amplifiers are designed to boost GPS signals for long range transmission or for a GPS Repeater Kit. Our filtered amplifier is ideal for boosting GPS signal in noisy environments. These amplifiers can also be used as a DC feeder for a GPS antenna, additional amplifier or as a DC splitter. The DC through can be regulated or by passed to the antenna for 5V systems.
Rojone – GPS Product Guide
Rojone has a full range of GPS products, to download a copy of our GPS catalogue click on the link below.
Military Circular Connectors
Rojone has been sourcing and supplying Military Circular Multipin connectors since we established in 1981. In addition, Rojone is able to custom manufacture cable looms to your specifications within our Ingleburn NSW plant.
Download Mil Circular Series catalogues below
Mil-C-5015 Series Connectors
Developed in 1939, the Mil-C 5015 series is one of the oldest connector ranges still on the market today. This series is classed as a general duties connector, commonly referred to as power connectors. The contact selection accommodates a range of wire sizes #0 to #16 American wire gauges, with 6 operating voltages.Main Characteristics – Material & Finish Aluminium alloy, olive drab.
Crimp & Solder versions are available, standard connector is screw/spin coupling although the range, part numbers suffixed with the letter “B” is a specialised 3 Lug bayonet coupling version. This range is environmentally resistant with a temperature range -55 to +125 Degrees C. A full range of dust caps, special contacts and back shells are also available.MIL-C-26482 Series 1 & 2 Connectors
Series 1 MS3100 to MS3119 are solder type, cost effective, general duty connectors. Series 2 are crimp, rear release connectors, ideal for more demanding applications requiring a higher temperature range of 175 to 200 Degrees C, fluid resistance, including the W Class with 500 hours salt spray. There are a range of conductive & non-conductive finishes as well as hermetic sealed options.MIL-C-38999 Series 1, 2, 3 & 4 Connectors
The Mil-C-38999 series of connectors were designed for both performance & mechanical robustness to meet a variety of demanding applications; Military, Aerospace, Ballistic Missile & Weapon Systems, and Marine Equipment.Common features applied to the D38999 family are compact size & weight, common mounting cut-outs, standard insert arrangements. Contacts, crimp tools, insertion/removal tools, sealing plus and assembly techniques are all standard across the whole MIL-C-38999 connector series.
The D38999 series offers excellent EMI Shielding up to 90dB, high durability with over 500 mating cycles, sine & random vibration specifications, firewall & scoop proof options.Series 1 & 2 are Bayonet coupling connectors, with Series 3 & 4 being screw coupling mating versions.
Low Smoke Zero Halogen – LMR Cable
Times Microwave represented by Rojone in Australia is pleased to introduce LMR- LSZH (Low Smoke Zero Halogen LMR Cable), as a lower
cost alternative to LMR-FR cables when CMR rate is not required.
Advanced features and benefits:
- Low Smoke Low Toxicity Non-halogen
- Flame: Meets IEC-332-1-2, IEC 332-3 CAT.C, UL-VW1, UL-1581, IEE-383, BS-
4066-1, BS-4066-3, UL-1685, NFPA-130 - Smoke: Meets IEC-61034-2, NES-711
- Halogen: Meets IEC-60754-1, BS 6425-1, IEC-60754-2, BS 6425-2
- UV Resistant: Meets UL-1581, 720 Hour UV Exposure
- Non-UL Listed Cable
- LMR connector, install tools and hardware accessories can be directly used
Size | Drawing No | MI Number | Order Code | |
---|---|---|---|---|
195 | 11761 | 54387 | LMR-195-LSZH | Datasheet |
200 | 11762 | 54388 | LMR-200-LHZH | Datasheet |
240 | 11763 | 54389 | LMR-240-LSZH | Datasheet |
240 | 11827 | 54397 | LMR-240-75-LSZH | Datasheet |
400 | 11764 | 54390 | LMR-400-LSZH | Datasheet |
400 | 11828 | 54398 | LMR-400-75-LSZH | Datasheet |
500 | 11765 | 54391 | LMR-500-LSZH | Datasheet |
600 | 11766 | 54392 | LMR-600-LSZH | Datasheet |
600 | 11829 | 54399 | LMR-600-75-LSHZ | Datasheet |
Times Microwave Systems specialises in the design & manufacture of high performance flexible, Low Loss, semi-rigid & standard coaxial M17 cable, for RF transmission from HF through Microwave frequencies DC to 46GHz.
What is LMR Cable? Times LMR Cables are high performance, broadband, flexible, low loss 50 and 75 Ohm coaxial communications cables designed for use in wireless applications such as;
2 way land mobile, IEEE<802.11a & 802.11b, Cellular, Wireless local loop, PCS, LMDS, Wireless Internet (WISP), MMDS, Broadband wireless data, CLEC, Telemetry, Paging, and many more.
LMR is a complete system of cables, connectors, installation tools & accessories – everything you need to make your job simple and successful.
What is the advantage of LMR? Times LMR cables have RF performance comparable to traditional corrugated copper cables, but unlike corrugated cables, LMR is highly flexible, non-kinking and offers unsurpassed ease and speed of connection installation. Compared to RG type braided cables, LMR offers far lower loss & better RF Shielding.
Are the LMR Series Cables exclusive to Times Microwave? Yes. LMR is a registered Trademark of Times Microwave. The LMR Series is a family of high quality communications cables & accessories designed and manufactured by Times Microwave USA.
Times Microwave manufactures high quality products; all cables are maked with the company brand, LMR trademark and code. Please be aware of inferior imitation cables and assemblies sold unlawfully as LMR series products.
Times Microwave has exclusively appointed Rojone its Australian agent, with their full support . We are the authorised stockist for their LMR series Low Loss cables, accessories & Military coaxial cable & assembly range.
LMR Standard Cable Codes
LMR 100A OD=0.110 inches, 2.79 mm
LMR 195 OD=0.195 inches, 4.95 mm
LMR 240 OD=0.240 inches, 6.10 mm
LMR 400 OD=0.405 inches, 10.29 mm
LMR 600 OD=0.590 inches, 14.99 mm
LMR 900 OD=0.870 inches, 22.10 mm
LMR 1200 OD=1.200 inches, 30.48mm
LMR 1700 OD=1.670 inches, 42.42mm
LMR Ultra Flex Cable Codes – Stranded center conductor & thermoplastic rubber jacket for maximum flexibility.
LMR 195-Ultra OD=0.195 inches, 4.95mm
LMR 240-Ultra OD=0.240 inches, 6.10mm
LMR 400-Ultra OD=0.405 inches, 10.29mm
LMR 600-Ultra OD=0.590 inches, 14.99 mm
LMR 75 Ohm Cable Codes
LMR 240-75 OD=0.240 inches, 6.10mm
LMR 400-75 OD=0.405 inches, 10.29mm
LMR 600-75 OD=0.590 inches, 14.99mm
Times LMR Specialized product, Light Weight LMR, Fire Retardant version, Low Smoke, Military.
LMR-FR – Fire retardant cable for installation in building vertical risers or where fire retardancy is critical, both UL & CSA listed (CMR/CATVR).
LMR-DB – Watertight cables with an inert flooding compound injected in the braid to completely eliminate the possibility of any water migration, with a 10 year warranty.
LMR-PVC – Polyvinylchloride outer jacket for enhanced flexibility.
New LMR-SW low loss, low PIM high performance 50 Ohm coax cable with a seamless alumnium outer conductor, providing superior durability in bending compared to seam-welded cables and superior electrical performance compared to corrugated cables. Compared to corrugated cables, LMR-SW cable is lighter and provides significant cost savings. The easily field installed connectors have superior weather sealing, VSWR and consistent PIM performance. LMR-SW cables are the perfect solution for PIM-sensitive installations such as full duplex transmission lines and co-located sites. They are suitable for short to medium height tower runs and flexible enough to be used as jumper cables in cell-sites and other RF applications up to 6 GHz. The high quality type N and 716 DIN connectors are user friendly and provide excellent and reliable performance when installed with the easy-to-use cable prep tools. Typical PIM performance better than -170dBc can be achieved consistently. Groundign kits, hangers and other installation accessories are also available. Available cables;
CABLE SIZE OD ATTENUATION db/100 ft
LMR-SW396 0.450″ 2.06 @ 450 MHz
3.00 @ 900 MHz
4.41 @ 1800 MHz
LMR-SW540 0.610″ 1.46 @ 450 MHz
2.11 @ 900 MHz
3.06 @ 1800 MHz
LLSB – Low Smoke, Low Loss Military Shipboard Cables, qualified to MIL-DTL-17 specifications commencing with M17/220 200LLSB throught to M17/228 1700LLSB.
195LLSB – 0.195 inch/4.95 mm OD Low Smoke, Low Loss cable is now available from Times Microwave and stocked in Australia by Rojone.
LLSB Performance Specifications 1MB
Other LMR products in the Times range;
- nu-TRAC TRC-1250
- LMR Bundled Cable 2.5MB
- LMR
- Flexible Low Loss
- Light Weight LMR 1MB
- LMR-DB
- Watertight – Flexible Low Loss
- LMR-FR Fire Retardant ‘Riser’
- LMR-LLPL Fire Retardant ‘Plenum’
- LMR-Ultraflex Repeated Flexing
- LMR-7575 ohm
- Leaky Radiating Cables
- T-RAD Low Cost Radiating Cable
- nu-TRAC Triaxial Radiating Cable
- TCOM Low PIM, Low Loss, Low Temperature
- UTCOM-UF Ultra Flexible
- TCOM-SF Super Flexible
- FBT Low Loss High Power
- Broadband
- M17-127-RG393
- General Purpose – rugged environments
- LLSB Low Smoke
- -FR rugged environments
- LLSB Low Loss Low Smoke
- -FR rugged environments
- SF M17’s with lower loss & superior shielding
- SFT Low Loss
- TFlex Flexible Alternative to Semirigid
- CL Traditional Semirigid
- CL Low Loss Semirigid
- RAD Low Coast Radiating Cable 0.5MB
- nu-TRAC Radiating Cable 0.2MB
- TCOM Low PIM, Low Loss, Low Temperature
- TCOM-400-UltraFlex 0.2MB
- TCOM-600-UltraFlex 0.2MB
- TCOM-400-FlexStrand-DB 0.2MB
- TCOM-600-FlexStrand-DB 0.2Mb
- RG &MG17 – Times Microwave Full Coaxial Cable handbook 2MB
- StripFlex lower loss & superior shielding flexible coax cable
- StripFlex “SF”
- StripFlex II “SFT”
- TFlex Flexible Alternative to Semi-Rigid
- Shipboard High Power 1MB
Download Cable Performance Calculators
Loss & Power Calculator VSWR & Return Loss Calculators
Times LMR Coaxial Connectors
Times LMR Accessories, Hangers, Tooling, etc
Habia Cable is a leading global supplier of standard & custom wire & electrical cables including equipment wire, twisted wire, signal cables, coaxial cables and triaxial cables for industrial, commercial, defence, nuclear and communications applications.
Stocked in their most popular Coax cable TZC-500-25 Silver plated, double shielded offering excellent loss & intermodulation characteristics. This cable has been designed into most Nokia/Ericsson base station radio sets.
Trompeter Electronics produces RF interconnect end products, cross-connects, and related tools for the Telecom, Central Office, Broadcast, Military Aerospace, and Instrumentation markets worldwide. In addition, the company has a broad line of patch panel insertion-controlled interconnect modules.
Rotary Joints – SPINNER Group (Germany)
Rotary joints are needed wherever high-frequency signals have to be transmitted between a fixed platform and a second platform in continuous rotation. Such applications include traditional radar technology for air traffic control or anti-missile defence, medical engineering, V-Sat and SatCom technology as well as TV camera systems or cable drums that allow sensitive cables to be wound up without twisting them, thus increasing their reliability.
In principle this can be achieved by three different technologies which mainly depend on the frequency of the transmitted signals:
-
Contacting transmission by slip rings
Depending on the unit size such contacting systems can transmit signals from
DC up to 120 MHz.
Coaxial contacting rotary joints
These SPINNER products allow signal transmission in the frequency range from
DC up to 50 GHz.
Contact-free rotary joints
Such extremely long-lived rotary joints are available as coaxial and waveguide
units. The maximum signal transmission bandwidth is about 20% of the upper
frequency to be transmitted.
The Spinner Company further offers:
-
Rotary joints for optical signal transmission
These can transmit up to 21 channels, as well as combinations of the individual types listed above in one rotary joint.
The special benefits of SPINNER rotary joints include their compact design, excellent VSWR and low attenuation loss, low variation of transmission properties during rotation, and high crosstalk attenuation between the individual channels over the whole frequency range.
With over 60 years of experience in RF technology SPINNER is in a position to develop and deliver any kind of rotary joint combination you may need.
Rotary Joints – Spinner (Germany)
Rotary joints are needed wherever high-frequency signals have to be transmitted between a fixed platform and a second platform in continuous rotation. Such applications include traditional radar technology for air traffic control or anti-missile defence, medical engineering, V-Sat and SatCom technology as well as TV camera systems or cable drums that allow sensitive cables to be wound up without twisting them, thus increasing their reliability.
In principle this can be achieved by three different technologies which mainly depend on the frequency of the transmitted signals:
-
Contacting transmission by slip rings
Depending on the unit size such contacting systems can transmit signals from
DC up to 120 MHz.
Coaxial contacting rotary joints
These SPINNER products allow signal transmission in the frequency range from
DC up to 50 GHz.
Contact-free rotary joints
Such extremely long-lived rotary joints are available as coaxial and waveguide
units. The maximum signal transmission bandwidth is about 20% of the upper
frequency to be transmitted.
The Spinner Company further offers:
-
Rotary joints for optical signal transmission
These can transmit up to 21 channels, as well as combinations of the individual types listed above in one rotary joint.
The special benefits of SPINNER rotary joints include their compact design, excellent VSWR and low attenuation loss, low variation of transmission properties during rotation, and high crosstalk attenuation between the individual channels over the whole frequency range.
With over 60 years of experience in RF technology SPINNER is in a position to develop and deliver any kind of rotary joint combination you may need.
Category 7, 100 Ohm
600 MHz Data Transmission Cables
The GIGA-DOR Solution is a complete line of high-performance Cat. 7 horizontal and work area data cables, designed for CLASS F links and for advanced high data-rate networks, available in a wide range of constructions.
GIGA-DOR Solution cables conform to the ISO/IEC 11801 requirements for Cat. 7 cables as specified in IEC 61156-5 and 61156-6. These cables are composed of balanced twisted pairs having a nominal 100 Ohm characteristic impedance up to 600 MHz, with a very high NEXT loss.
The high NEXT loss, achieved by individual aluminium foil pair shields, provides a typical margin of 60 dB ACR over U/UTP cables, making GIGA-Solution cables ideal for multiple high-frequency services.
GIGA-DOR & GIGA-DOR Jr. S/FTP horizontal cables and GIGA-Patch 4 pair S/FTP 26 AWG work area (patch) cables are overall shielded with a tin-coated copper braid. When properly grounded, this copper braid and the individual aluminium foil shields provide exceptional EMC performance, having a minimum coupling attenuation of 90 dB.
All cables are available with flame-retardant PVC or halogen-free (HFFR) jackets, in a range of colors, in single or “Siamese” twin (FIG-8) constructions.
Category 7 Data Transmission Cables
Part Number | Product Description | Computer & LAN Applications | Outer Jacket Material | Outer Jacket Material (mm nom.) |
---|---|---|---|---|
9928244xxx | Cat. 7 4x2x26/7 AWG S/FTP Work Area FR-LSZH | High data rates | FR-LSZH | 6.4 |
9928264xxx | Cat. 7 4x2x26/7 AWG S/FTP Work Area PU | Outdoor installations | PU | 6.5 |
9928312xxx | Cat. 7 12x(4x2x26/7 AWG S/FTP) Multi-Cable Work Area FR-LSZH | Indoor Backbone | FR-LSZH | 27.8 |
9827A54xxx | Cat. 7 4x2x23/1 AWG F/FTP FRLSZH | Indoor use, fixed installations | FR-LSZH | 7.4 |
9928675xxx | Cat. 7 1000 MHz 4x2x23/1 AWG S/FTP FR-LSZH | Indoor use, fixed installations | FR-LSZH | 7.5 |
9928654xxx | Cat. 7 4x2x23/1 AWG S/FTP FRLSZH | Data-Centers/SANs | FR-LSZH | 8.0 |
9928554xxx | Cat. 7 4x2x22/1 AWG S/FTP FRLSZH | Indoor use, fixed installations | FR-LSZH | 8.2 |
9928692xxx | Cat. 7 2x(4x2x23/1 AWG) FIG-8 S/FTP FR-LSZH | Data-Centers/SANs | FR-LSZH | 8.0 |
9928604xxx | Cat. 7 4x2x23/1 AWG S/FTP FR-PVC | Indoor use, fixed installations | FR-PVC | 7.8 |
9928659xxx | Cat. 7 4x2x23/1 AWG S/FTP CSA Direct Burial PE | Outdoor and direct burial installations | PE | 12.0 |
CLIC® Cable & Pipe Fastening
Original 100% Swiss made, proven reliability since 1975
-
Secure, fast and economical
All-in-one, self-locking
Plastic clamps
CLIC® – The ‘clever’ fastening solution
-
• Single-handed installation
• Saves up to 40% installation time in comparison to commonly used clamps
• Tested & approved by all the major international CA’s
• Resistant to chemicals
• Non-corrosive, weather resistant
• Fire performance
• Halogen & phosphor free
• Noise absorbing
• Wide Diameter Range
CLIC® Cable & Pipe Fastening Applications
Ideal for public areas, building infrastructure Telecommunications, electrical, radiating cables, fire alarm systems, marine for water and compressed air, chemical industry, clean rooms, mining & broadcast tunnel communications.
LP-GPX-05-S 1000 – 2000MHz SMA, Lightning & Surge Protection
The LP-GPX-05-S high performance series is an exceptional DC pass design for protection of GPS receivers requiring up to 5Vdc power to be supplied on the center
pin.
While the RF path is DC blocked, the biased DC voltage protection circuit uses Solid State protection technology to provide unsurpassed surge performance. The LP-GPX-
05-S series offers outstanding Insertion Loss and Return Loss characteristics over the 1000-2000MHz band, making it suitable for protection of commercial and military GPS, as well as other applications in this band.
Unlike competitive protectors, the white bronze plated construction of the LP-GPX-05-S series eliminates potential galvanic corrosion issues and provides long life in hostile environments. The fully weatherized housing is sealed to IP65 allowing for outdoor as well as indoor
5 allowing for outdoor as well as indoor
installation.
LP-GPX-05-S 1000 – 2000MHz SMA, Lightning & Surge Protection
LP-GTX-05 TNC Series L1, L2 & L3 &GPS Lightning & Surge Protection
LP-GTX-05-T high performance series is an exceptional DC pass design for protection of GPS receivers requiring up to 5Vdc power to be supplied on the center pin.
While the RF path is DC blocked, the biased DC voltage protection circuit uses Solid State
Protection Technology to provide unsurpassed surge performance. The LP-GPSX-05-T series offers outstanding insertion loss and return Loss characteristics over the 1000-2000 MHz band, making it suitable for protection of commercial and military GPS, as well as other applications in this band.
LP-GTX-05 N Series L1, L2 & L3 & GPS Lightning & Surge Protection
LP-GTX-05-N high performance series is an exceptional DC pass design for protection of GPS receivers requiring up to 5Vdc power to be supplied on the center pin.
While the RF path is DC blocked, the biased DC voltage protection circuit uses Solid State
Protection Technology to provide unsurpassed surge performance. The LP-GPSX-05-N series offers outstanding insertion loss and return Loss characteristics over the 1000-2000 MHz band, making it suitable for protection of commercial and military GPS, as well as other applications in this band.
LP-GTR-D 7/16 DIN Series GPS Lightning & Surge Protection
LP-GTR-D is an exception broadband DC pass design for lightening protection applications requiring DC power to be supplied to the electronics. This is the perfect protection solution for distributed antenna systems, tower mounted amplifiers and GPS Systems and other applications requiring DC pass circuitry. These devices exhibit outstanding RF performance with high surge current handling from 50-550 Watts.
Fully weatherized housing meets IP67 standard allowing for both indoor and outdoor installation.
Rojone – GPS Product Guide
Rojone has a full range of GPS products, to download a copy of our GPS catalogue click on the link below.